Datalogic M-Series Dokumentacja Strona 168
- Strona / 203
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
DRAGON™
156
5
5.10 CONFIGURATION EDITING COMMANDS
The following commands carry out their specific function and then exit the
configuration environment.
Command Description
iPk
iPk
iPk
Restore DRAGON™ reader default configuration (see
the relative Quick Reference Manual for default
settings)
i,k
i,k
i,k
Transmit the DRAGON™ D or DRAGON™ M Software
release
i@k
i@k
i@k
Transmit DRAGON™ reader configuration in ASCII
format.
This command is not effective with Pen emulation
interface.
i39Rk
i39Rk
i39Rk
Restore OM-DRAGON™ default configuration (see the
Quick Reference Manual for default settings)
i39Wk
i39Wk
i39Wk
Transmit the OM-DRAGON™ Software release
i39\k
i39\k
i39\k
Transmit OM-DRAGON™ configuration in ASCII
format.
This command is not effective with Pen emulation
interface.
- Reference Manual 1
- CONTENTS 5
- GENERAL VIEW 11
- Figure C – OM-DRAGON™ 12
- Figure D – C-DRAGON™ 12
- 1 INTRODUCTION 13
- 2 INSTALLATION 14
- INSTALLATION 15
- CAUTION 15
- OM-DRAGON™ connectors 15
- 2.3 RS232 CONNECTION 16
- 2.4 WEDGE CONNECTION 16
- 2.6 NETWORK CONNECTIONS 17
- 2.6.2 Network Cabling 18
- 2.6.3 Network Termination 19
- 2.7.1 Battery Type 19
- 2.7.2 Battery Charging 20
- 2. Open the battery cover 21
- 1. Carefully clean the 23
- 2. Remove the protective 23
- 5. Insert the antenna in the 24
- 2. Carefully clean 24
- 2.8.3 Wall Mounting 25
- Alignment Plate Holes 26
- 3.1 STAND ALONE LAYOUTS 27
- 3.1.1 Single Reader Layout 27
- 3.1.4 C-Box Layout 29
- 3.2.1 Host Master Layout 30
- /*32: FAIL*/ 32
- 4 CONFIGURATION 33
- 4.2 SETUP PROCEDURES 34
- 4.3 DRAGON™ D SETUP 35
- 4.7 INTERFACE SELECTION 43
- VT2xx/VT3xx/VT4xx 46
- APPLE ADB Bus 46
- CONFIGURATION 47
- RS232 PARAMETERS 48
- BAUD RATE 49
- DATA BITS 50
- STOP BITS 51
- HANDSHAKING 51
- ACK/NACK PROTOCOL 52
- INTER-CHARACTER DELAY 53
- RX TIMEOUT 53
- WEDGE PARAMETERS 55
- KEYBOARD NATIONALITY 56
- CAPS LOCK 58
- AUTO-RECOGNITION 58
- NUM LOCK 59
- INTER-CODE DELAY 60
- KEYBOARD SETTING 61
- CONTROL CHARACTER EMULATION 63
- PEN EMULATION 64
- OPERATING MODE 65
- MINIMUM OUTPUT PULSE 66
- OVERFLOW 68
- OUTPUT LEVEL 68
- IDLE LEVEL 69
- INTER-BLOCK DELAY 69
- NETWORK PARAMETERS 70
- RS485 NETWORK 71
- NETWORK BAUD RATE 72
- SLAVE ADDRESS RANGE 72
- WARNING MESSAGE 73
- MASTER CRADLE HEADER 74
- MASTER CRADLE TERMINATOR 75
- DATA FORMAT 76
- CODE IDENTIFIER TABLE 77
- CODE IDENTIFIER 79
- CUSTOM CODE IDENTIFIER 80
- TERMINATOR 82
- FIELD ADJUSTMENT 83
- FIELD ADJUSTMENT CHARACTER 84
- CODE LENGTH TX 84
- CHARACTER REPLACEMENT 85
- POWER SAVE 89
- SLEEP STATE 90
- ENTER SLEEP TIMEOUT 90
- READING PARAMETERS 91
- TRIGGER TYPE 92
- TRIGGER SIGNAL 92
- TRIGGER-OFF TIMEOUT 93
- FLASH MODE 93
- READS PER CYCLE 94
- SAFETY TIME 94
- BEEPER INTENSITY 95
- BEEPER TONE 95
- AIMING SYSTEM 96
- INK-SPREAD 98
- OVERFLOW CONTROL 98
- INTERDIGIT CONTROL 99
- DECODING SAFETY 99
- DECODING PARAMETERS 100
- PUZZLE SOLVER™ 100
- CODE SELECTION 101
- EAN/UPC FAMILY 103
- 2/5 FAMILY 107
- CODE 39 FAMILY 108
- CODE 128 FAMILY 110
- CODE 93 111
- CODABAR FAMILY 112
- PLESSEY 115
- TELEPEN 116
- DELTA IBM 117
- CODE 11 118
- CODE 16K 119
- CODE 49 119
- RSS CODES 120
- ADVANCED FORMATTING 121
- CONCATENATION 122
- RADIO PARAMETERS 140
- RADIO PROTOCOL TIMEOUT 141
- POWER-OFF TIMEOUT 141
- TRANSMISSION MODE 142
- BATTERY TYPE 143
- SINGLE STORE 144
- BATCH MODE 145
- DISPLAY PARAMETERS 146
- DATE AND TIME 147
- CONTRAST 147
- FONT SIZE 148
- BACKLIGHT 148
- DISPLAY-OFF TIMEOUT 148
- DISPLAY MODE 149
- 5 REFERENCES 150
- 5.1.2 ACK/NACK Protocol 151
- 5.1.3 FIFO 152
- 5.1.4 RX Timeout 153
- 5.2 PEN PARAMETERS 153
- 5.2.1 Minimum Output Pulse 153
- 5.2.3 Overflow 154
- 5.2.5 Inter-Block Delay 155
- 5.3 NETWORK PARAMETERS 155
- 5.3.2 Warning Message 155
- 5.4 DATA FORMAT 156
- Enter configuration 158
- DRAGON™ M Series Only 159
- 5.4.3 Address Stamping 160
- 5.4.4 Address Delimiter 160
- 5.4.5 Time Stamping Format 160
- REFERENCES 161
- 5.6.3 Reads per Cycle 162
- 5.6.4 Safety Time 162
- 5.8.2 Power-Off Timeout 164
- 5.8.3 Transmission Mode 164
- 5.8.5 Single Store 165
- 5.8.6 Batch Mode 166
- 5.9.1 Display Mode 167
- 5.11.1 Copy DRAGON 169
- D-Series 169
- 5.11.2 Copy DRAGON 170
- M-Series 170
- 5.11.3 Copy OM-DRAGON™ 171
- 5.12 C-DRAGON™ CONFIGURATION 172
- 6 MESSAGE FORMATTING 173
- 6.1.1 Cursor Control 174
- 6.1.2 Font Selection 175
- 6.1.3 Clearing Display 175
- 6.1.5 Setting RTC 176
- [Terminator] 177
- 7 TECHNICAL FEATURES 178
- 7.2 DRAGON™ M 179
- 7.3 OM-DRAGON™ / C-DRAGON™ 180
- 7.5 STATUS INDICATORS 181
- DRAGON™ 182
- 7.6 READING DIAGRAMS 183
- HOST CONFIGURATION STRINGS 185
- SERIAL CONFIGURATION STRINGS 186
- B CODE IDENTIFIER TABLE 198
- C HEX AND NUMERIC TABLE 201
- HEX / NUMERIC TABLE 202
Powiązane produkty i podręczniki dla Networking Datalogic M-Series
Networking Datalogic M-Series Instrukcja Obsługi
(134 strony)
(134 strony)
Networking Datalogic Star Instrukcja Instalacji
(36 strony)
(36 strony)
Networking Datalogic Star Instrukcja Instalacji
(128 strony)
(128 strony)
(38 strony)
(4 strony)
Networking Datalogic QLM700 Instrukcja Obsługi
(142 strony)
(142 strony)
© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.177 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji